Skip to content
Plans from £3.54/mo · Billed once, no auto-renewal · Login on WhatsApp in minutes
See plans
Currency
See plans

TV guide (EPG) not loading on IPTV? Try these steps

Troubleshooting cover card asking TV guide (EPG) not loading on IPTV? Try these steps, beside a TV icon

Short answer

When channels play but the guide stays blank, the guide has usually not finished building, the player was set up with the M3U link instead of the Xtream Codes login, or the app simply has no guide. Give it a few minutes, run the guide update in the player's settings, restart the device and, where you can, move to the Xtream Codes login.

On this page
  1. Why is the IPTV EPG not loading when the channels play?
  2. Has the guide had time to build after a new setup?
  3. Did you sign in with Xtream Codes or the M3U link?
  4. How do you force the guide to refresh?
  5. Does your player show a guide on this device at all?
  6. Does the guide load on another device with the same login?
  7. Is the guide missing, or just showing the wrong times?
  8. Would restarting the device help the guide load?
  9. Why does the guide fail on a smart TV, MAG or Formuler box?
  10. What if only some channels have no guide?
  11. How does the guide connect to catch-up?
  12. What should you avoid while the guide is blank?
  13. When should you message us about the guide?
  14. Bottom line

IPTV EPG not loading is one of the most common evening puzzles: the channels play, but the guide grid is blank, says "no information" or never finishes loading. The good news is that the cause is nearly always one of a handful of settings, and none of them needs new equipment.

This guide skips the theory and goes straight to the checks, in the order that solves the problem fastest. If no channels play at all, the issue is bigger than the guide, and our two-minute outage check is the better place to start.

Why is the IPTV EPG not loading when the channels play?

Because the channels and the guide listings travel separately, and the listings can fail or lag while the video works. The usual causes are a guide still building after setup, a login type that does not carry the guide, or an app that has no guide to show.

Before you change anything, match your situation to a row in this table. It points you to the right section below.

What you notice Likely cause Go to
Brand new setup, guide blank Listings still building Has the guide had time to build?
Set up with a single playlist link The M3U link may need a separate guide address Xtream Codes or M3U
Guide was fine, now blank Old guide data stuck in the app Force a guide refresh
Watching in VLC or by casting The player has no guide on the TV Does your player show a guide?
Listings there, but at the wrong times Time zone or guide offset Is it missing, or just wrong?

Listings and 7-day catch-up are part of every plan, so a blank guide is a fault to fix, not a missing feature.

Has the guide had time to build after a new setup?

Often the guide is simply not ready yet. A new activation or a freshly added login needs a few minutes before the listings appear, even though the channels play straight away.

Leave the device switched on with the player open on the live section. After a few minutes, restart the device once, then open the guide again. On a MAG box, this one reboot after activation is often all it takes.

Patience has a limit, though. If the guide is still empty an hour after activation, the listings are not just slow. Send us a WhatsApp message with a screenshot of the blank guide, and we look at your line from our side.

This is the most common reason for IPTV EPG not loading in an app that does have a guide. The Xtream Codes login brings the guide with it, while the M3U link may need a guide address of its own.

Every order includes both login types. The Xtream Codes login is made of three details: server address, username and password. An app that accepts it pulls in channels, categories, films, series and the guide together. The M3U link is one playlist address that suits players without Xtream Codes support.

Xtream Codes login M3U link
What you enter Server URL, username, password One playlist address
TV guide Loads together with the channels May need its own guide address
Catch-up Connects on its own Can be limited
Best for Any player that accepts it Players that only take a playlist URL, such as VLC

If your player offers both and you used the playlist link, remove that entry and sign in again with the Xtream Codes details from our WhatsApp message. The guide should then load together with the channels.

How do you force the guide to refresh?

Players with a guide usually offer a refresh or update option for it in their settings, and running it clears stale listings. Follow it with a full restart of the app.

Look in the player’s settings for the guide, EPG or programme section and choose the refresh or update option. Then quit the app properly, since the Back button alone often leaves it running, and start it afresh. Give the grid a minute to fill before you scroll.

The exact wording of the option differs from app to app, and we will not guess menu names here. Our setup guides for every device show each player we support, and if you cannot find the option, send us a photo of the settings screen on WhatsApp.

On an iPhone or iPad, pull down on the channel list to refresh it, then close the app from the app switcher and reopen it.

Does your player show a guide on this device at all?

Not every way of watching includes a guide, so a blank grid is sometimes normal. Check your player and device here before you spend time on settings.

Player or method TV guide on screen?
IBO Player Yes
IPTV Smarters and Smarters Player Lite Yes
MyTVOnline 3 on Formuler, with the Xtream Codes login Yes
MAG box built-in portal Yes
VLC on Windows or Mac No, it plays the playlist without a guide
Casting to a Roku with Web Video Caster Not on the TV, it stays on the phone

VLC is handy for proving that channels play, yet it never draws a listings grid. When you cast to a Roku, the television receives the picture alone, while the listings remain on the phone.

If you want a full guide on the TV, a player installed on the TV or a streaming stick is the answer. Our explainer on what an IPTV player does shows how the app and the service split the work.

Does the guide load on another device with the same login?

Trying a second screen tells you whether the fault sits in one device or further up the chain. If the guide appears on a phone or laptop with the same login, our listings are reaching you, and the first device’s app or settings need attention.

Install a guide-capable player on the second device and sign in with the Xtream Codes details. Open the live section and look at the grid. If it fills there, go back to the first device and work through the refresh and restart steps again, or try the login in a different player.

If the grid stays blank on both screens, there is little point repeating the same steps. That pattern is worth a WhatsApp message to us with screenshots from each device.

Is the guide missing, or just showing the wrong times?

Check this before you go further. A guide that lists programmes at the wrong hour has loaded correctly, and the fix is the clock, not the guide.

Set the time zone on the device to your own city first, then reopen the guide. If times are still out by an hour, the player or portal has a guide offset you can shift in steps of an hour. Clock changes in spring and autumn can shift it again.

Wrong times and a missing guide feel similar from the sofa, but they are different faults. This guide covers the missing one.

Would restarting the device help the guide load?

Yes, a full restart often fixes a guide that hangs halfway, because it clears memory the player needs to draw the grid. It also makes the app reload the listings from scratch.

Use a proper restart rather than the TV remote’s standby button. On a Samsung or LG TV, unplug the set at the wall for a minute. On a stick or box, restart it from its own settings. Then open the player and give it a moment before opening the guide.

If the guide loads slowly on a busy evening, the connection can play a part too. On a slow connection, the very first load of listings can be sluggish. Our IPTV speed test tells you what your connection delivers.

Why does the guide fail on a smart TV, MAG or Formuler box?

Each of these has one extra thing to check, because the guide reaches them in a slightly different way.

  • Samsung and LG TVs: players such as IBO Player are activated from the TV’s MAC address or Device ID. Confirm we have activated it, quit the app properly, power-cycle the TV, then run the guide refresh. The Samsung and LG TV guide shows the activation route.
  • MAG boxes: the portal fills the guide after activation. Choose your time zone in the settings before judging it, and reboot once. Our MAG box setup guide walks through the portal.
  • Formuler with MyTVOnline 3: select the portal again and wait a minute while the categories load. Still nothing? Power the box off and on, then let it rejoin your network.

What if only some channels have no guide?

Then the guide itself works, and the gap is limited to those channels. Note their names and tell us on WhatsApp, so we can check the listings from our side.

Scroll through two or three groups to see how widespread it is. If most channels show listings and a few do not, there is no need to reset your player. Changing apps or logins will not help either, because the guide is clearly reaching the device.

How does the guide connect to catch-up?

Catch-up uses the same listings, so a missing guide usually means catch-up is missing too. Fix the guide first and catch-up tends to return with it.

With the Xtream Codes login, catch-up links up by itself as soon as the guide is in place. With the M3U link, catch-up can be limited. Our guide to watching the last 7 days with IPTV catch-up explains how to use it once the grid is back.

What should you avoid while the guide is blank?

Avoid unofficial apps and web players that promise a better guide. They are not needed, and handing your login to an unknown site puts your account at risk.

Install players only from official sources. That means the TV’s own app store, Google Play, Apple’s App Store or a developer’s own download page, such as the IBO Player downloads page or the official IPTV Smarters site. Never type your login into a browser page that offers to play channels for you.

It also pays to change one thing at a time. If you refresh the guide, switch login type and change player all at once, you will not know which step worked.

When should you message us about the guide?

Message us in three cases: the guide is still blank an hour after activation, it stays empty after a refresh and a restart, or it fails on a second device too. At that point the cause is likely on our side.

Send a short note on WhatsApp with the player you use, the login type, the device and a screenshot of the empty guide. Replies come daily, usually within the hour. If the picture also stops on a still frame, mention it, and see our fixes for a frozen picture.

Bottom line

IPTV EPG not loading almost always comes down to time, login type or the player. Wait a few minutes after setup and sign in with the Xtream Codes login rather than the M3U link. Then refresh the guide in the player settings and restart the device. If you watch in VLC or by casting, the blank grid is normal and a guide-capable player is the fix.

If none of that brings the listings back within an hour, send us a screenshot and we check from our end. Each plan on our IPTV UK subscription page comes with the full guide and a week of catch-up, from £3.54 a month.

Frequently asked questions

How long does the TV guide take to appear after setup?

A fresh setup needs a few minutes before the listings fill in, so give it time before you change anything. Keep the device switched on for a while, then reboot it a single time. Should the grid remain empty an hour after activation, send us a WhatsApp message with a screenshot and we check your line from our side.

Why do the channels work but the guide does not?

Channels and listings arrive separately, so one can load without the other. The most common reasons are a guide that is still building, a login made with the M3U link, where the listings can need a separate address, or an app that has no guide to show. Switching to the Xtream Codes login fixes most cases.

Does VLC show a TV guide?

No. VLC handles the playlist link well, yet it never draws listings, so an empty grid there is expected rather than a fault. Use it as a quick test that channels play, then set up IBO Player or IPTV Smarters on the same computer if you want listings.

Can I see a TV guide when casting to a Roku?

Not on the TV itself. When you cast, the television receives the picture alone, and the listings remain in the app on your phone. That is a limit of casting, not of your plan. For listings on the TV, use a player installed on the TV or a streaming stick.

Is a guide with the wrong times the same problem?

No, that is a different fault with a different fix. A guide that shows programmes at the wrong times has loaded fine, but the time zone on the device or the guide offset in the player is off. Pick your own city in the device's time zone setting, then nudge the guide offset an hour at a time until it matches.

Is the TV guide included in every plan?

Yes. Whether your plan covers 1, 2 or 3 devices, it includes Full EPG and 7-day catch-up. The guide shows in any player that supports one, such as IBO Player, IPTV Smarters or the built-in portal on a MAG box. You can compare plan lengths and device counts on our IPTV UK subscription page.

Need help? Chat on WhatsApp

Plans from £3.54/moBilled once, no auto-renewal

See plans